收藏本站
LT3743
APPLICATIONS INFORMATION
Thermal Shutdown
The internal thermal shutdown within the LT3743 engages
at 163°C and terminates switching, resets soft-start and
shuts down the PWMGL and PWMGH drivers. When the part
has cooled to 155°C, the internal reset is cleared and soft-
start is allowed to charge once the PWM signal is asserted.
Switching Frequency Synchronization
The nominal switching frequency of the LT3743 is determined
by the resistor from the RT pin to ground and may be set
from 200kHz to 1MHz. The internal oscillator may also be
synchronized to an external clock through the SYNC pin. The
external clock applied to the SYNC pin must have a logic low
below 0.3V and a logic high higher than 1.25V. The input fre-
quency must be 20% higher than the frequency determined
by the resistor at the RT pin. Input signals outside of these
specified parameters will cause erratic switching behavior
and subharmonic oscillations. The synchronization range
is 240kHz to 1.2MHz. Synchronization is tested at 500kHz
with a 200k R T resistor. Operation under other conditions is
guaranteed by design. When synchronizing to an external
clock, please be aware that there will be a fixed delay from the
input clock edge to the edge of switch. The SYNC pin must
be grounded if the synchronization to an external clock is not
required. When SYNC is grounded, the switching frequency
is determined by the resistor at the RT pin.
Shutdown and UVLO
The LT3743 has an internal UVLO that terminates switching,
resets all synchronous logic, and discharges the soft-start
capacitor for input voltages below 4.2V. The LT3743 also
has a precision shutdown at 1.55V on the EN/UVLO pin.
Partial shutdown occurs at 1.55V and full shutdown is
guaranteed below 0.5V with <1μA I Q in the full shutdown
state. Below 1.5V, an internal current source provides
5.5μA of pull-down current to allow for programmable
UVLO hysteresis. The following equations determine the
voltage divider resistors for programming the UVLO volt-
age and hysteresis as configured in Figure 14.
The EN/UVLO pin as an absolute maximum voltage of
6V. To accommodate the largest range of applications,
there is an internal Zener diode that clamps this pin. For
applications where the supply range is greater than 4:1,
size R2 greater than 375k.
V IN V IN
LT3743 R2
EN/UVLO
R1
3743 F14
Figure 14. UVLO Configuration
LED Current Derating Using the CTRL_T Pin
The LT3743 is designed specifically for driving high
current LEDs. Most high current LEDs require derating
the maximum current based on operating temperature
to prevent damage to the LED. In addition, many
applications have thermal limitations that will require the
regulated current to be reduced based on LED and/or
board temperature. To achieve this, the LT3743 uses the
CTRL_T pin to reduce the effective regulated current in
the LED for both the high and low control currents. While
CTRL_H and CTRL_L program the regulated current in the
LED, CTRL_T can be configured to reduce this regulated
current based on the analog voltage at the CTRL_T pin.
The LED/board temperature derating is programmed using
a resistor divider with a temperature dependant resistance
(Figure 15). When the board/LED temperature rises, the
CTRL_T voltage will decrease. To reduce the regulated
current, the CTRL_T voltage must be lower than voltage
at the CTRL_L and CTRL_H pins.
R V R V
V REF
R2 LT3743 R NTC R NTC R X R NTC R NTC R X
CTRL_T 3743 F15
V HYST
? 1.55V ? R2 ?
R2 =
5.5μA
R1 = ? ?
? V UVLO – 1.55V ?
R1 A B C
(OPTION A TO D)
Figure 15. LED Current Derating vs Temperature
Using NTC Resistor
D
3743fd
19
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LT3745IUJ#TRPBF IC LED DVR 16CH 50MA 40QFN
LT3746IUHH#TRPBF IC LED DRIVER 32CHANNEL 56-QFN
LT3754IUH#TRPBF IC LED DVR 16CH 50MA 32QFN
LT3755EMSE#PBF IC LED DRVR HP CONS CURR 16-MSOP
LT3760EFE#PBF IC LED DVR WHT/CLR BCKLT 28TSSOP
LT3799IMSE#PBF IC LED DRIVER TRIAC DIM 16-MSOP
LT3956EUHE#PBF IC LED DVR BUCK BOOST 36-VQFN
LTC3201EMS#TRPBF IC LED DRVR WHITE BCKLGT 10-MSOP
相关代理商/技术参数
LT3743EFE#PBF 制造商:Linear Technology 功能描述:IC LED DRIVER BUCK TSSOP-28
LT3743EFE#TRPBF 功能描述:IC LED DVR SYNC STEPDOWN 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3743EFEPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:High Current Synchronous Step-Down LED Driver with Three-State Control
LT3743EFETRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:High Current Synchronous Step-Down LED Driver with Three-State Control
LT3743EUFD#PBF 功能描述:IC LED DRVR HP CONST CURR 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C
LT3743EUFD#PBF 制造商:Linear Technology 功能描述:IC LED DRIVER BUCK QFN-28 制造商:Linear Technology 功能描述:IC, LED DRIVER, BUCK, QFN-28
LT3743EUFD#TRPBF 功能描述:IC LED DVR SYNC STEP-DOWN 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3743EUFDPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:High Current Synchronous Step-Down LED Driver with Three-State Control